groove angle
英 [ɡruːv ˈæŋɡl]
美 [ɡruːv ˈæŋɡl]
n. （凹，齿）槽角；（焊缝）坡口角度
双语例句
- Investigation about Effect of Flash Groove Wedge Angle of Forging Dies on Filling Ability
锻模毛边槽楔角对充满性影响的研究 - The method of cold work hardening is applied to increase the permanence limit and to decrease the compressive stress of groove and little round angle of turn angle on mechanic components.
采用表面硬化处理的方法，使机械构件上沟槽、转角的小圆角处的持久极限得到提高，减少构件的应力集中危害。 - Meantime, the mathematical model of the groove angle and the local dihedral is also deduced.
并且推导了局部两面角和坡口角数学模型。 - Through utilizing deep groove rollers, solve coal slip problem when big declivitous angle belt conveyor working.
通过采用深槽托辊组解决了大倾角带式输送机物料的下滑问题； - The joint shapes suited for CO_2 welding are designed Under which weld quality is still assured but the groove angle and size of fillet weld are reduced. By ways of these the productivity is increased and cost decreased.
提出了适合于CO2焊特点的接头形式，该接头形式在保证焊接质量前提下，减小了对接焊的坡口角度及角焊缝的焊脚尺寸，可以提高焊接生产率，降低成本。 - The experimental results show that both the depth and the radius exert an influence on the stress concentration at the groove bottom remarkably, and the influence of the flare angle can be neglected.
实验研究表明，槽深、槽底圆角半径对槽底应力集中水平的影响最大，而槽外形夹角对槽底应力集中水平的影响程度最小。 - New Method of Machining Internal Spiral Groove of a Big Lift Angle
大升角内螺旋槽加工新方法 - The results show that reducing the carbon content, enlarging the welding groove angle, and using alternating current as well as high welding voltage in submerged arc welding are all beneficial to improve the low temperature toughness.
结果表明：降低碳含量、增大焊接坡口角度，以及在埋弧焊中采用交流电源和高焊接电压均能改善焊接接头的低温韧性。 - Design of Chip-hold Groove of Shaping Miller with Positive Rake Angle
正前角成形铣刀容屑槽 - This paper presents a calculating method for the edge of a new hob with straight groove and zero rake angle. The original section edge of the said hob is on the surface of basic worm.
本文提出了对直槽零前角滚刀，原始截面刃形在基本蜗杆齿面上，其新滚刀刃形的计算方法。 - This paper introduces effect, structure and working principle of equipment making conveying belt change groove angle.
介绍了试验台上输送带可变成槽装置的作用、结构及工作原理。 - The method of weld groove angle is adopted in the system, leading to an improved welding quality and efficiency, and thus saving the welding materials.
系统采用了焊接坡口角形式，提高了焊接质量和效率，节约了焊接材料。 - The highest of dog bone arised at the middle of slab length. The stability would increase by using edging roller with groove and slope angle.
立轧后板坯头、尾部存在不同程度的失宽，狗骨高度最大值出现在板坯中部，采用孔型立辊或锥形立辊可提高轧制过程的稳定性。 - Effect of narrow-gap groove angle on ultrasonic tandem testing
窄间隙焊缝坡口角度对超声波串列式扫查影响研究 - Analysis of transmission deviation of belt conveyer and groove angle effect on correcting the deviation
带式输送机跑偏分析及槽角对防偏纠偏能力的影响 - Direction of the bone groove was ante inferior to post superior, and form 30 ° angle.
骨槽方向为前下后上并与水平线成30°角。 - The patterns etched are of high resolution, and the groove depth and groove wall angle can be controlled with less surface stress.
具有极高的分辨率，能够控制槽深和槽壁角度，表面应力小。 - An Analysis of Groove Angle on the Column Intersection Line and Its Cutting
圆柱相贯线焊接坡口角及切割的分析 - The relationship of these major parameters such as groove numbers and spiral angle to seal pressure is revealed and the optimized result is obtained.
分析了影响密封性能的主要设计参数如螺旋角α，槽数n等对密封压力的影响规律，得出了优化结果。 - The optimization model of sealing ability for a bushing helical seal is presented. In this model, the maximum value of sealing coefficient is objective function, and the relative groove depth, the relative groove width and helical angle are designed variables.
以密封系数最大为优化目标函数，考虑了相对槽深、相对槽宽和螺旋角等约束条件，建立了螺套式螺旋密封封液能力优化的数学模型。 - Equipment making conveying belt change groove angle of the belt conveyor's test device
带式输送机试验台输送带成槽装置 - The cylindrical line of intersection and the welding groove angle were cut in the scene, they all meets the welding technical accuracy after measuring.
现场切割了筒体相贯线和焊接坡口，经检测满足焊接技术要求。 - The influences of operational pressure and structural parameters, such as taper, breadth rate of dam zone, depth of dynamic pressure groove, number of dynamic pressure groove and spiral angle, on the starting and stopping performance of dry gas seal are studied.
分析了操作参数，如操作压力，和端面结构参数，如锥度、坝宽比、槽深、螺旋角等，对干气密封启停性能的影响。 - Aiming at the difficulty of machining internal spiral groove with big lift angle, several methods are presented.
针对大升角的内螺旋槽加工的难点，提出了几种加工方法，并制造出了样机。 - The cutting of various complex graphics has been realized in the flat steel, which proved the feasibility of the parametric programming algorithm. The cutting path with changing bevel has been finished and the groove angle meets the cutting requirements in working conditions.
在扁钢上实现了各种复杂图形的切割，验证了参数化编程算法的可行性，在扁钢上完成了变坡口切割路径的切割，切割坡口角度满足工况条件的切割要求。 - The main works in this paper were done as follows: 1. The cutting track curve of cylindrical intersection and the cutting methods of the line of intersection and the welding groove angle were set by describing the cutting principle of cylindrical line of intersection. 2.
论文主要完成以下工作：1.通过对简体相贯线切割原理的描述，建立了筒体相贯的切割轨迹曲线，确定了相贯线切割和焊接坡口角切割方法。 - On the choice of groove parameters, the influences of groove parameters ( such as groove depth, groove opening angle and groove root radius) on the groove bottom stress concentration extent were analyzed by finite element method.
在切口参数的选择上，本文使用有限元方法分析了切口深度、切口张开角度及切口根部圆角半径等对切口处应力集中程度的影响。 - The following are the works in this thesis: ( 1) The structural characteristics and important concepts of deep groove ball bearing such as contact angle, curvature, goodness of fit, are introduced.
本文的主要做了以下工作：（1）介绍深沟球轴承的结构特点以及密合度、接触角、曲率等几个重要的轴承概念。 - The conclusion is reached that the relative slip between the ball and groove is unavoidable, and with the increase of contact angle and lead angle, the revolution speed and spin speed is enlarged. 3.
理论研究发现，滚珠丝杠副中滚珠与螺旋滚道之间的相对滑动是不可避免的，随着接触角和螺旋升角的增大，滚珠公转速度和自转角速度都会增大。